smartctl 5.41 2011-06-09 r3365 [x86_64-linux-3.0.0-23-generic] (local build) Copyright (C) 2002-11 by Bruce Allen, http://smartmontools.sourceforge.net === START OF INFORMATION SECTION === Model Family: Western Digital Caviar Green Device Model: WDC WD6400AACS-00G8B0 Serial Number: WD-WCAUF1015941 LU WWN Device Id: 5 0014ee 201e5b9ac Firmware Version: 05.04C05 User Capacity: 640.135.028.736 bytes [640 GB] Sector Size: 512 bytes logical/physical Device is: In smartctl database [for details use: -P show] ATA Version is: 8 ATA Standard is: Exact ATA specification draft version not indicated Local Time is: Sat Aug 4 19:48:29 2012 CEST SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x84) Offline data collection activity was suspended by an interrupting command from host. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (15180) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 176) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x303f) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 200 200 051 - 768 3 Spin_Up_Time POS--K 137 131 021 - 6133 4 Start_Stop_Count -O--CK 098 098 000 - 2973 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate -OSR-K 100 253 051 - 0 9 Power_On_Hours -O--CK 093 093 000 - 5466 10 Spin_Retry_Count -O--CK 100 100 051 - 0 11 Calibration_Retry_Count -O--CK 100 100 051 - 0 12 Power_Cycle_Count -O--CK 098 098 000 - 2968 192 Power-Off_Retract_Count -O--CK 200 200 000 - 134 193 Load_Cycle_Count -O--CK 200 200 000 - 2973 194 Temperature_Celsius -O---K 112 103 000 - 35 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--CK 200 200 000 - 100 198 Offline_Uncorrectable ----CK 200 200 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0 200 Multi_Zone_Error_Rate ---R-- 200 200 051 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] GP/S Log at address 0x00 has 1 sectors [Log Directory] SMART Log at address 0x01 has 1 sectors [Summary SMART error log] SMART Log at address 0x02 has 5 sectors [Comprehensive SMART error log] GP Log at address 0x03 has 6 sectors [Ext. Comprehensive SMART error log] SMART Log at address 0x06 has 1 sectors [SMART self-test log] GP Log at address 0x07 has 1 sectors [Extended self-test log] SMART Log at address 0x09 has 1 sectors [Selective self-test log] GP Log at address 0x10 has 1 sectors [NCQ Command Error] GP Log at address 0x11 has 1 sectors [SATA Phy Event Counters] GP/S Log at address 0x80 has 16 sectors [Host vendor specific log] GP/S Log at address 0x81 has 16 sectors [Host vendor specific log] GP/S Log at address 0x82 has 16 sectors [Host vendor specific log] GP/S Log at address 0x83 has 16 sectors [Host vendor specific log] GP/S Log at address 0x84 has 16 sectors [Host vendor specific log] GP/S Log at address 0x85 has 16 sectors [Host vendor specific log] GP/S Log at address 0x86 has 16 sectors [Host vendor specific log] GP/S Log at address 0x87 has 16 sectors [Host vendor specific log] GP/S Log at address 0x88 has 16 sectors [Host vendor specific log] GP/S Log at address 0x89 has 16 sectors [Host vendor specific log] GP/S Log at address 0x8a has 16 sectors [Host vendor specific log] GP/S Log at address 0x8b has 16 sectors [Host vendor specific log] GP/S Log at address 0x8c has 16 sectors [Host vendor specific log] GP/S Log at address 0x8d has 16 sectors [Host vendor specific log] GP/S Log at address 0x8e has 16 sectors [Host vendor specific log] GP/S Log at address 0x8f has 16 sectors [Host vendor specific log] GP/S Log at address 0x90 has 16 sectors [Host vendor specific log] GP/S Log at address 0x91 has 16 sectors [Host vendor specific log] GP/S Log at address 0x92 has 16 sectors [Host vendor specific log] GP/S Log at address 0x93 has 16 sectors [Host vendor specific log] GP/S Log at address 0x94 has 16 sectors [Host vendor specific log] GP/S Log at address 0x95 has 16 sectors [Host vendor specific log] GP/S Log at address 0x96 has 16 sectors [Host vendor specific log] GP/S Log at address 0x97 has 16 sectors [Host vendor specific log] GP/S Log at address 0x98 has 16 sectors [Host vendor specific log] GP/S Log at address 0x99 has 16 sectors [Host vendor specific log] GP/S Log at address 0x9a has 16 sectors [Host vendor specific log] GP/S Log at address 0x9b has 16 sectors [Host vendor specific log] GP/S Log at address 0x9c has 16 sectors [Host vendor specific log] GP/S Log at address 0x9d has 16 sectors [Host vendor specific log] GP/S Log at address 0x9e has 16 sectors [Host vendor specific log] GP/S Log at address 0x9f has 16 sectors [Host vendor specific log] GP/S Log at address 0xa0 has 16 sectors [Device vendor specific log] GP/S Log at address 0xa1 has 16 sectors [Device vendor specific log] GP/S Log at address 0xa2 has 16 sectors [Device vendor specific log] GP/S Log at address 0xa3 has 16 sectors [Device vendor specific log] GP/S Log at address 0xa4 has 16 sectors [Device vendor specific log] GP/S Log at address 0xa5 has 16 sectors [Device vendor specific log] GP/S Log at address 0xa6 has 16 sectors [Device vendor specific log] GP/S Log at address 0xa7 has 16 sectors [Device vendor specific log] GP/S Log at address 0xa8 has 1 sectors [Device vendor specific log] GP/S Log at address 0xa9 has 1 sectors [Device vendor specific log] GP/S Log at address 0xaa has 1 sectors [Device vendor specific log] GP/S Log at address 0xab has 1 sectors [Device vendor specific log] GP/S Log at address 0xac has 1 sectors [Device vendor specific log] GP/S Log at address 0xad has 1 sectors [Device vendor specific log] GP/S Log at address 0xae has 1 sectors [Device vendor specific log] GP/S Log at address 0xaf has 1 sectors [Device vendor specific log] GP/S Log at address 0xb0 has 1 sectors [Device vendor specific log] GP/S Log at address 0xb1 has 1 sectors [Device vendor specific log] GP/S Log at address 0xb2 has 1 sectors [Device vendor specific log] GP/S Log at address 0xb3 has 1 sectors [Device vendor specific log] GP/S Log at address 0xb4 has 1 sectors [Device vendor specific log] GP/S Log at address 0xb5 has 1 sectors [Device vendor specific log] GP/S Log at address 0xb6 has 1 sectors [Device vendor specific log] GP/S Log at address 0xb7 has 1 sectors [Device vendor specific log] GP/S Log at address 0xc0 has 1 sectors [Device vendor specific log] GP Log at address 0xc1 has 24 sectors [Device vendor specific log] GP/S Log at address 0xe0 has 1 sectors [SCT Command/Status] GP/S Log at address 0xe1 has 1 sectors [SCT Data Transfer] SMART Extended Comprehensive Error Log Version: 1 (6 sectors) Device Error Count: 210 (device log contains only the most recent 24 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 210 [17] occurred at disk power-on lifetime: 5466 hours (227 days + 18 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 49 b9 00 c4 48 40 00 Error: UNC at LBA = 0x49b900c448 = 316636447816 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 c0 00 00 00 00 49 c4 b9 48 40 08 00:13:42.018 READ FPDMA QUEUED 61 00 08 00 00 00 00 47 9b 29 98 40 08 00:13:42.018 WRITE FPDMA QUEUED 61 00 08 00 00 00 00 4a 32 59 c0 40 08 00:13:42.018 WRITE FPDMA QUEUED 60 00 08 00 00 00 00 49 f3 50 50 40 08 00:13:42.004 READ FPDMA QUEUED 60 00 08 00 00 00 00 47 2b 58 a8 40 08 00:13:41.994 READ FPDMA QUEUED Error 209 [16] occurred at disk power-on lifetime: 5466 hours (227 days + 18 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 49 b9 00 c4 48 40 00 Error: UNC at LBA = 0x49b900c448 = 316636447816 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 c0 00 08 00 00 49 c4 b9 48 40 08 00:13:38.687 READ FPDMA QUEUED 60 00 48 00 00 00 00 49 c4 b9 00 40 08 00:13:38.686 READ FPDMA QUEUED 61 00 08 00 30 00 00 4a 32 59 b8 40 08 00:13:38.678 WRITE FPDMA QUEUED 61 00 08 00 08 00 00 4a 32 59 b0 40 08 00:13:38.678 WRITE FPDMA QUEUED 61 00 08 00 00 00 00 4a 32 59 a8 40 08 00:13:38.677 WRITE FPDMA QUEUED Error 208 [15] occurred at disk power-on lifetime: 5466 hours (227 days + 18 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 47 0c 00 15 d0 40 00 Error: UNC at LBA = 0x470c0015d0 = 305144010192 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 00 00 00 47 15 0c d0 40 08 05:26:17.720 READ FPDMA QUEUED ef 00 10 00 02 00 00 00 00 00 00 a0 08 05:26:17.720 SET FEATURES [Reserved for Serial ATA] 27 00 00 00 00 00 00 00 00 00 00 e0 08 05:26:17.720 READ NATIVE MAX ADDRESS EXT ec 00 00 00 00 00 00 00 00 00 00 a0 08 05:26:17.719 IDENTIFY DEVICE ef 00 03 00 46 00 00 00 00 00 00 a0 08 05:26:17.719 SET FEATURES [Set transfer mode] Error 207 [14] occurred at disk power-on lifetime: 5466 hours (227 days + 18 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 47 0c 00 15 d0 40 00 Error: UNC at LBA = 0x470c0015d0 = 305144010192 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 00 00 00 47 15 0c d0 40 08 05:26:14.457 READ FPDMA QUEUED ef 00 10 00 02 00 00 00 00 00 00 a0 08 05:26:14.457 SET FEATURES [Reserved for Serial ATA] 27 00 00 00 00 00 00 00 00 00 00 e0 08 05:26:14.457 READ NATIVE MAX ADDRESS EXT ec 00 00 00 00 00 00 00 00 00 00 a0 08 05:26:14.456 IDENTIFY DEVICE ef 00 03 00 46 00 00 00 00 00 00 a0 08 05:26:14.456 SET FEATURES [Set transfer mode] Error 206 [13] occurred at disk power-on lifetime: 5466 hours (227 days + 18 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 47 0c 00 15 d0 40 00 Error: UNC at LBA = 0x470c0015d0 = 305144010192 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 00 00 00 47 15 0c d0 40 08 05:26:11.049 READ FPDMA QUEUED ef 00 10 00 02 00 00 00 00 00 00 a0 08 05:26:11.049 SET FEATURES [Reserved for Serial ATA] 27 00 00 00 00 00 00 00 00 00 00 e0 08 05:26:11.049 READ NATIVE MAX ADDRESS EXT ec 00 00 00 00 00 00 00 00 00 00 a0 08 05:26:11.048 IDENTIFY DEVICE ef 00 03 00 46 00 00 00 00 00 00 a0 08 05:26:11.048 SET FEATURES [Set transfer mode] Error 205 [12] occurred at disk power-on lifetime: 5466 hours (227 days + 18 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 47 0c 00 15 d0 40 00 Error: UNC at LBA = 0x470c0015d0 = 305144010192 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 28 00 00 48 5c 56 40 40 08 05:26:07.897 READ FPDMA QUEUED 60 00 20 00 20 00 00 48 c8 78 80 40 08 05:26:07.897 READ FPDMA QUEUED 60 00 40 00 18 00 00 48 c8 78 a8 40 08 05:26:07.897 READ FPDMA QUEUED 60 00 08 00 10 00 00 48 c8 79 00 40 08 05:26:07.897 READ FPDMA QUEUED 60 00 70 00 08 00 00 48 c8 79 10 40 08 05:26:07.897 READ FPDMA QUEUED Error 204 [11] occurred at disk power-on lifetime: 5466 hours (227 days + 18 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 47 0c 00 15 d0 40 00 Error: UNC at LBA = 0x470c0015d0 = 305144010192 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 70 00 c0 00 00 48 c8 79 10 40 08 05:26:04.750 READ FPDMA QUEUED 60 00 08 00 b8 00 00 48 c8 79 00 40 08 05:26:04.750 READ FPDMA QUEUED 60 00 40 00 b0 00 00 48 c8 78 a8 40 08 05:26:04.750 READ FPDMA QUEUED 60 00 20 00 a8 00 00 48 c8 78 80 40 08 05:26:04.750 READ FPDMA QUEUED 60 00 08 00 a0 00 00 48 5c 56 40 40 08 05:26:04.750 READ FPDMA QUEUED Error 203 [10] occurred at disk power-on lifetime: 5466 hours (227 days + 18 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 47 0c 00 15 d0 40 00 Error: UNC at LBA = 0x470c0015d0 = 305144010192 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 18 00 00 47 15 0c d0 40 08 05:26:01.360 READ FPDMA QUEUED 60 00 10 00 10 00 00 47 10 05 48 40 08 05:26:01.360 READ FPDMA QUEUED 61 00 08 00 08 00 00 47 37 6e 10 40 08 05:26:01.360 WRITE FPDMA QUEUED 60 00 08 00 00 00 00 49 77 0d b8 40 08 05:26:01.360 READ FPDMA QUEUED ea 00 00 00 00 00 00 00 00 00 00 e0 08 05:26:01.326 FLUSH CACHE EXT SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 2 SCT Version (vendor specific): 258 (0x0102) SCT Support Level: 1 Device State: SMART Off-line Data Collection executing in background (4) Current Temperature: 35 Celsius Power Cycle Min/Max Temperature: 27/35 Celsius Lifetime Min/Max Temperature: 27/45 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -41/85 Celsius Temperature History Size (Index): 478 (400) Index Estimated Time Temperature Celsius 401 2012-08-04 11:51 39 ******************** ... ..( 91 skipped). .. ******************** 15 2012-08-04 13:23 39 ******************** 16 2012-08-04 13:24 40 ********************* ... ..(131 skipped). .. ********************* 148 2012-08-04 15:36 40 ********************* 149 2012-08-04 15:37 ? - 150 2012-08-04 15:38 27 ******** 151 2012-08-04 15:39 27 ******** 152 2012-08-04 15:40 28 ********* 153 2012-08-04 15:41 29 ********** 154 2012-08-04 15:42 29 ********** 155 2012-08-04 15:43 29 ********** 156 2012-08-04 15:44 30 *********** 157 2012-08-04 15:45 30 *********** 158 2012-08-04 15:46 30 *********** 159 2012-08-04 15:47 31 ************ 160 2012-08-04 15:48 32 ************* 161 2012-08-04 15:49 32 ************* 162 2012-08-04 15:50 32 ************* 163 2012-08-04 15:51 33 ************** ... ..( 2 skipped). .. ************** 166 2012-08-04 15:54 33 ************** 167 2012-08-04 15:55 34 *************** ... ..( 4 skipped). .. *************** 172 2012-08-04 16:00 34 *************** 173 2012-08-04 16:01 35 **************** 174 2012-08-04 16:02 40 ********************* ... ..( 29 skipped). .. ********************* 204 2012-08-04 16:32 40 ********************* 205 2012-08-04 16:33 ? - 206 2012-08-04 16:34 27 ******** 207 2012-08-04 16:35 27 ******** 208 2012-08-04 16:36 28 ********* 209 2012-08-04 16:37 29 ********** 210 2012-08-04 16:38 30 *********** ... ..( 5 skipped). .. *********** 216 2012-08-04 16:44 30 *********** 217 2012-08-04 16:45 31 ************ ... ..( 2 skipped). .. ************ 220 2012-08-04 16:48 31 ************ 221 2012-08-04 16:49 32 ************* ... ..( 3 skipped). .. ************* 225 2012-08-04 16:53 32 ************* 226 2012-08-04 16:54 33 ************** 227 2012-08-04 16:55 33 ************** 228 2012-08-04 16:56 33 ************** 229 2012-08-04 16:57 34 *************** ... ..( 6 skipped). .. *************** 236 2012-08-04 17:04 34 *************** 237 2012-08-04 17:05 35 **************** ... ..( 12 skipped). .. **************** 250 2012-08-04 17:18 35 **************** 251 2012-08-04 17:19 36 ***************** ... ..( 15 skipped). .. ***************** 267 2012-08-04 17:35 36 ***************** 268 2012-08-04 17:36 37 ****************** 269 2012-08-04 17:37 38 ******************* 270 2012-08-04 17:38 37 ****************** ... ..( 6 skipped). .. ****************** 277 2012-08-04 17:45 37 ****************** 278 2012-08-04 17:46 ? - 279 2012-08-04 17:47 25 ****** 280 2012-08-04 17:48 26 ******* 281 2012-08-04 17:49 26 ******* 282 2012-08-04 17:50 27 ******** ... ..( 3 skipped). .. ******** 286 2012-08-04 17:54 27 ******** 287 2012-08-04 17:55 28 ********* 288 2012-08-04 17:56 28 ********* 289 2012-08-04 17:57 28 ********* 290 2012-08-04 17:58 29 ********** 291 2012-08-04 17:59 29 ********** 292 2012-08-04 18:00 30 *********** ... ..( 3 skipped). .. *********** 296 2012-08-04 18:04 30 *********** 297 2012-08-04 18:05 31 ************ 298 2012-08-04 18:06 31 ************ 299 2012-08-04 18:07 31 ************ 300 2012-08-04 18:08 32 ************* 301 2012-08-04 18:09 33 ************** ... ..( 2 skipped). .. ************** 304 2012-08-04 18:12 33 ************** 305 2012-08-04 18:13 34 *************** ... ..( 3 skipped). .. *************** 309 2012-08-04 18:17 34 *************** 310 2012-08-04 18:18 35 **************** 311 2012-08-04 18:19 35 **************** 312 2012-08-04 18:20 36 ***************** ... ..( 2 skipped). .. ***************** 315 2012-08-04 18:23 36 ***************** 316 2012-08-04 18:24 35 **************** 317 2012-08-04 18:25 36 ***************** ... ..( 2 skipped). .. ***************** 320 2012-08-04 18:28 36 ***************** 321 2012-08-04 18:29 35 **************** 322 2012-08-04 18:30 36 ***************** ... ..( 8 skipped). .. ***************** 331 2012-08-04 18:39 36 ***************** 332 2012-08-04 18:40 37 ****************** 333 2012-08-04 18:41 38 ******************* ... ..( 39 skipped). .. ******************* 373 2012-08-04 19:21 38 ******************* 374 2012-08-04 19:22 39 ******************** ... ..( 25 skipped). .. ******************** 400 2012-08-04 19:48 39 ******************** SCT Error Recovery Control: Read: Disabled Write: Disabled SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x000a 2 1 Device-to-host register FISes sent due to a COMRESET 0x8000 4 1463 Vendor specific