smartctl.2012-08-04-19-48.log (24,69 KB)
smartctl 5.41 2011-06-09 r3365 [x86_64-linux-3.0.0-23-generic] (local build)
Copyright (C) 2002-11 by Bruce Allen, http://smartmontools.sourceforge.net
=== START OF INFORMATION SECTION ===
Model Family: Western Digital Caviar Green
Device Model: WDC WD6400AACS-00G8B0
Serial Number: WD-WCAUF1015941
LU WWN Device Id: 5 0014ee 201e5b9ac
Firmware Version: 05.04C05
User Capacity: 640.135.028.736 bytes [640 GB]
Sector Size: 512 bytes logical/physical
Device is: In smartctl database [for details use: -P show]
ATA Version is: 8
ATA Standard is: Exact ATA specification draft version not indicated
Local Time is: Sat Aug 4 19:48:29 2012 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x84) Offline data collection activity
was suspended by an interrupting command from host.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: (15180) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 176) minutes.
Conveyance self-test routine
recommended polling time: ( 5) minutes.
SCT capabilities: (0x303f) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE
1 Raw_Read_Error_Rate POSR-K 200 200 051 - 768
3 Spin_Up_Time POS--K 137 131 021 - 6133
4 Start_Stop_Count -O--CK 098 098 000 - 2973
5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0
7 Seek_Error_Rate -OSR-K 100 253 051 - 0
9 Power_On_Hours -O--CK 093 093 000 - 5466
10 Spin_Retry_Count -O--CK 100 100 051 - 0
11 Calibration_Retry_Count -O--CK 100 100 051 - 0
12 Power_Cycle_Count -O--CK 098 098 000 - 2968
192 Power-Off_Retract_Count -O--CK 200 200 000 - 134
193 Load_Cycle_Count -O--CK 200 200 000 - 2973
194 Temperature_Celsius -O---K 112 103 000 - 35
196 Reallocated_Event_Count -O--CK 200 200 000 - 0
197 Current_Pending_Sector -O--CK 200 200 000 - 100
198 Offline_Uncorrectable ----CK 200 200 000 - 0
199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0
200 Multi_Zone_Error_Rate ---R-- 200 200 051 - 0
||||||_ K auto-keep
|||||__ C event count
||||___ R error rate
|||____ S speed/performance
||_____ O updated online
|______ P prefailure warning
General Purpose Log Directory Version 1
SMART Log Directory Version 1 [multi-sector log support]
GP/S Log at address 0x00 has 1 sectors [Log Directory]
SMART Log at address 0x01 has 1 sectors [Summary SMART error log]
SMART Log at address 0x02 has 5 sectors [Comprehensive SMART error log]
GP Log at address 0x03 has 6 sectors [Ext. Comprehensive SMART error log]
SMART Log at address 0x06 has 1 sectors [SMART self-test log]
GP Log at address 0x07 has 1 sectors [Extended self-test log]
SMART Log at address 0x09 has 1 sectors [Selective self-test log]
GP Log at address 0x10 has 1 sectors [NCQ Command Error]
GP Log at address 0x11 has 1 sectors [SATA Phy Event Counters]
GP/S Log at address 0x80 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x81 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x82 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x83 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x84 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x85 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x86 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x87 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x88 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x89 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x8a has 16 sectors [Host vendor specific log]
GP/S Log at address 0x8b has 16 sectors [Host vendor specific log]
GP/S Log at address 0x8c has 16 sectors [Host vendor specific log]
GP/S Log at address 0x8d has 16 sectors [Host vendor specific log]
GP/S Log at address 0x8e has 16 sectors [Host vendor specific log]
GP/S Log at address 0x8f has 16 sectors [Host vendor specific log]
GP/S Log at address 0x90 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x91 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x92 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x93 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x94 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x95 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x96 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x97 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x98 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x99 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x9a has 16 sectors [Host vendor specific log]
GP/S Log at address 0x9b has 16 sectors [Host vendor specific log]
GP/S Log at address 0x9c has 16 sectors [Host vendor specific log]
GP/S Log at address 0x9d has 16 sectors [Host vendor specific log]
GP/S Log at address 0x9e has 16 sectors [Host vendor specific log]
GP/S Log at address 0x9f has 16 sectors [Host vendor specific log]
GP/S Log at address 0xa0 has 16 sectors [Device vendor specific log]
GP/S Log at address 0xa1 has 16 sectors [Device vendor specific log]
GP/S Log at address 0xa2 has 16 sectors [Device vendor specific log]
GP/S Log at address 0xa3 has 16 sectors [Device vendor specific log]
GP/S Log at address 0xa4 has 16 sectors [Device vendor specific log]
GP/S Log at address 0xa5 has 16 sectors [Device vendor specific log]
GP/S Log at address 0xa6 has 16 sectors [Device vendor specific log]
GP/S Log at address 0xa7 has 16 sectors [Device vendor specific log]
GP/S Log at address 0xa8 has 1 sectors [Device vendor specific log]
GP/S Log at address 0xa9 has 1 sectors [Device vendor specific log]
GP/S Log at address 0xaa has 1 sectors [Device vendor specific log]
GP/S Log at address 0xab has 1 sectors [Device vendor specific log]
GP/S Log at address 0xac has 1 sectors [Device vendor specific log]
GP/S Log at address 0xad has 1 sectors [Device vendor specific log]
GP/S Log at address 0xae has 1 sectors [Device vendor specific log]
GP/S Log at address 0xaf has 1 sectors [Device vendor specific log]
GP/S Log at address 0xb0 has 1 sectors [Device vendor specific log]
GP/S Log at address 0xb1 has 1 sectors [Device vendor specific log]
GP/S Log at address 0xb2 has 1 sectors [Device vendor specific log]
GP/S Log at address 0xb3 has 1 sectors [Device vendor specific log]
GP/S Log at address 0xb4 has 1 sectors [Device vendor specific log]
GP/S Log at address 0xb5 has 1 sectors [Device vendor specific log]
GP/S Log at address 0xb6 has 1 sectors [Device vendor specific log]
GP/S Log at address 0xb7 has 1 sectors [Device vendor specific log]
GP/S Log at address 0xc0 has 1 sectors [Device vendor specific log]
GP Log at address 0xc1 has 24 sectors [Device vendor specific log]
GP/S Log at address 0xe0 has 1 sectors [SCT Command/Status]
GP/S Log at address 0xe1 has 1 sectors [SCT Data Transfer]
SMART Extended Comprehensive Error Log Version: 1 (6 sectors)
Device Error Count: 210 (device log contains only the most recent 24 errors)
CR = Command Register
FEATR = Features Register
COUNT = Count (was: Sector Count) Register
LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8
LH = LBA High (was: Cylinder High) Register ] LBA
LM = LBA Mid (was: Cylinder Low) Register ] Register
LL = LBA Low (was: Sector Number) Register ]
DV = Device (was: Device/Head) Register
DC = Device Control Register
ER = Error register
ST = Status register
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 210 [17] occurred at disk power-on lifetime: 5466 hours (227 days + 18 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 49 b9 00 c4 48 40 00 Error: UNC at LBA = 0x49b900c448 = 316636447816
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
60 00 c0 00 00 00 00 49 c4 b9 48 40 08 00:13:42.018 READ FPDMA QUEUED
61 00 08 00 00 00 00 47 9b 29 98 40 08 00:13:42.018 WRITE FPDMA QUEUED
61 00 08 00 00 00 00 4a 32 59 c0 40 08 00:13:42.018 WRITE FPDMA QUEUED
60 00 08 00 00 00 00 49 f3 50 50 40 08 00:13:42.004 READ FPDMA QUEUED
60 00 08 00 00 00 00 47 2b 58 a8 40 08 00:13:41.994 READ FPDMA QUEUED
Error 209 [16] occurred at disk power-on lifetime: 5466 hours (227 days + 18 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 49 b9 00 c4 48 40 00 Error: UNC at LBA = 0x49b900c448 = 316636447816
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
60 00 c0 00 08 00 00 49 c4 b9 48 40 08 00:13:38.687 READ FPDMA QUEUED
60 00 48 00 00 00 00 49 c4 b9 00 40 08 00:13:38.686 READ FPDMA QUEUED
61 00 08 00 30 00 00 4a 32 59 b8 40 08 00:13:38.678 WRITE FPDMA QUEUED
61 00 08 00 08 00 00 4a 32 59 b0 40 08 00:13:38.678 WRITE FPDMA QUEUED
61 00 08 00 00 00 00 4a 32 59 a8 40 08 00:13:38.677 WRITE FPDMA QUEUED
Error 208 [15] occurred at disk power-on lifetime: 5466 hours (227 days + 18 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 47 0c 00 15 d0 40 00 Error: UNC at LBA = 0x470c0015d0 = 305144010192
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
60 00 08 00 00 00 00 47 15 0c d0 40 08 05:26:17.720 READ FPDMA QUEUED
ef 00 10 00 02 00 00 00 00 00 00 a0 08 05:26:17.720 SET FEATURES [Reserved for Serial ATA]
27 00 00 00 00 00 00 00 00 00 00 e0 08 05:26:17.720 READ NATIVE MAX ADDRESS EXT
ec 00 00 00 00 00 00 00 00 00 00 a0 08 05:26:17.719 IDENTIFY DEVICE
ef 00 03 00 46 00 00 00 00 00 00 a0 08 05:26:17.719 SET FEATURES [Set transfer mode]
Error 207 [14] occurred at disk power-on lifetime: 5466 hours (227 days + 18 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 47 0c 00 15 d0 40 00 Error: UNC at LBA = 0x470c0015d0 = 305144010192
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
60 00 08 00 00 00 00 47 15 0c d0 40 08 05:26:14.457 READ FPDMA QUEUED
ef 00 10 00 02 00 00 00 00 00 00 a0 08 05:26:14.457 SET FEATURES [Reserved for Serial ATA]
27 00 00 00 00 00 00 00 00 00 00 e0 08 05:26:14.457 READ NATIVE MAX ADDRESS EXT
ec 00 00 00 00 00 00 00 00 00 00 a0 08 05:26:14.456 IDENTIFY DEVICE
ef 00 03 00 46 00 00 00 00 00 00 a0 08 05:26:14.456 SET FEATURES [Set transfer mode]
Error 206 [13] occurred at disk power-on lifetime: 5466 hours (227 days + 18 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 47 0c 00 15 d0 40 00 Error: UNC at LBA = 0x470c0015d0 = 305144010192
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
60 00 08 00 00 00 00 47 15 0c d0 40 08 05:26:11.049 READ FPDMA QUEUED
ef 00 10 00 02 00 00 00 00 00 00 a0 08 05:26:11.049 SET FEATURES [Reserved for Serial ATA]
27 00 00 00 00 00 00 00 00 00 00 e0 08 05:26:11.049 READ NATIVE MAX ADDRESS EXT
ec 00 00 00 00 00 00 00 00 00 00 a0 08 05:26:11.048 IDENTIFY DEVICE
ef 00 03 00 46 00 00 00 00 00 00 a0 08 05:26:11.048 SET FEATURES [Set transfer mode]
Error 205 [12] occurred at disk power-on lifetime: 5466 hours (227 days + 18 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 47 0c 00 15 d0 40 00 Error: UNC at LBA = 0x470c0015d0 = 305144010192
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
60 00 08 00 28 00 00 48 5c 56 40 40 08 05:26:07.897 READ FPDMA QUEUED
60 00 20 00 20 00 00 48 c8 78 80 40 08 05:26:07.897 READ FPDMA QUEUED
60 00 40 00 18 00 00 48 c8 78 a8 40 08 05:26:07.897 READ FPDMA QUEUED
60 00 08 00 10 00 00 48 c8 79 00 40 08 05:26:07.897 READ FPDMA QUEUED
60 00 70 00 08 00 00 48 c8 79 10 40 08 05:26:07.897 READ FPDMA QUEUED
Error 204 [11] occurred at disk power-on lifetime: 5466 hours (227 days + 18 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 47 0c 00 15 d0 40 00 Error: UNC at LBA = 0x470c0015d0 = 305144010192
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
60 00 70 00 c0 00 00 48 c8 79 10 40 08 05:26:04.750 READ FPDMA QUEUED
60 00 08 00 b8 00 00 48 c8 79 00 40 08 05:26:04.750 READ FPDMA QUEUED
60 00 40 00 b0 00 00 48 c8 78 a8 40 08 05:26:04.750 READ FPDMA QUEUED
60 00 20 00 a8 00 00 48 c8 78 80 40 08 05:26:04.750 READ FPDMA QUEUED
60 00 08 00 a0 00 00 48 5c 56 40 40 08 05:26:04.750 READ FPDMA QUEUED
Error 203 [10] occurred at disk power-on lifetime: 5466 hours (227 days + 18 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 47 0c 00 15 d0 40 00 Error: UNC at LBA = 0x470c0015d0 = 305144010192
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
60 00 08 00 18 00 00 47 15 0c d0 40 08 05:26:01.360 READ FPDMA QUEUED
60 00 10 00 10 00 00 47 10 05 48 40 08 05:26:01.360 READ FPDMA QUEUED
61 00 08 00 08 00 00 47 37 6e 10 40 08 05:26:01.360 WRITE FPDMA QUEUED
60 00 08 00 00 00 00 49 77 0d b8 40 08 05:26:01.360 READ FPDMA QUEUED
ea 00 00 00 00 00 00 00 00 00 00 e0 08 05:26:01.326 FLUSH CACHE EXT
SMART Extended Self-test Log Version: 1 (1 sectors)
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
SCT Status Version: 2
SCT Version (vendor specific): 258 (0x0102)
SCT Support Level: 1
Device State: SMART Off-line Data Collection executing in background (4)
Current Temperature: 35 Celsius
Power Cycle Min/Max Temperature: 27/35 Celsius
Lifetime Min/Max Temperature: 27/45 Celsius
Under/Over Temperature Limit Count: 0/0
SCT Temperature History Version: 2
Temperature Sampling Period: 1 minute
Temperature Logging Interval: 1 minute
Min/Max recommended Temperature: 0/60 Celsius
Min/Max Temperature Limit: -41/85 Celsius
Temperature History Size (Index): 478 (400)
Index Estimated Time Temperature Celsius
401 2012-08-04 11:51 39 ********************
... ..( 91 skipped). .. ********************
15 2012-08-04 13:23 39 ********************
16 2012-08-04 13:24 40 *********************
... ..(131 skipped). .. *********************
148 2012-08-04 15:36 40 *********************
149 2012-08-04 15:37 ? -
150 2012-08-04 15:38 27 ********
151 2012-08-04 15:39 27 ********
152 2012-08-04 15:40 28 *********
153 2012-08-04 15:41 29 **********
154 2012-08-04 15:42 29 **********
155 2012-08-04 15:43 29 **********
156 2012-08-04 15:44 30 ***********
157 2012-08-04 15:45 30 ***********
158 2012-08-04 15:46 30 ***********
159 2012-08-04 15:47 31 ************
160 2012-08-04 15:48 32 *************
161 2012-08-04 15:49 32 *************
162 2012-08-04 15:50 32 *************
163 2012-08-04 15:51 33 **************
... ..( 2 skipped). .. **************
166 2012-08-04 15:54 33 **************
167 2012-08-04 15:55 34 ***************
... ..( 4 skipped). .. ***************
172 2012-08-04 16:00 34 ***************
173 2012-08-04 16:01 35 ****************
174 2012-08-04 16:02 40 *********************
... ..( 29 skipped). .. *********************
204 2012-08-04 16:32 40 *********************
205 2012-08-04 16:33 ? -
206 2012-08-04 16:34 27 ********
207 2012-08-04 16:35 27 ********
208 2012-08-04 16:36 28 *********
209 2012-08-04 16:37 29 **********
210 2012-08-04 16:38 30 ***********
... ..( 5 skipped). .. ***********
216 2012-08-04 16:44 30 ***********
217 2012-08-04 16:45 31 ************
... ..( 2 skipped). .. ************
220 2012-08-04 16:48 31 ************
221 2012-08-04 16:49 32 *************
... ..( 3 skipped). .. *************
225 2012-08-04 16:53 32 *************
226 2012-08-04 16:54 33 **************
227 2012-08-04 16:55 33 **************
228 2012-08-04 16:56 33 **************
229 2012-08-04 16:57 34 ***************
... ..( 6 skipped). .. ***************
236 2012-08-04 17:04 34 ***************
237 2012-08-04 17:05 35 ****************
... ..( 12 skipped). .. ****************
250 2012-08-04 17:18 35 ****************
251 2012-08-04 17:19 36 *****************
... ..( 15 skipped). .. *****************
267 2012-08-04 17:35 36 *****************
268 2012-08-04 17:36 37 ******************
269 2012-08-04 17:37 38 *******************
270 2012-08-04 17:38 37 ******************
... ..( 6 skipped). .. ******************
277 2012-08-04 17:45 37 ******************
278 2012-08-04 17:46 ? -
279 2012-08-04 17:47 25 ******
280 2012-08-04 17:48 26 *******
281 2012-08-04 17:49 26 *******
282 2012-08-04 17:50 27 ********
... ..( 3 skipped). .. ********
286 2012-08-04 17:54 27 ********
287 2012-08-04 17:55 28 *********
288 2012-08-04 17:56 28 *********
289 2012-08-04 17:57 28 *********
290 2012-08-04 17:58 29 **********
291 2012-08-04 17:59 29 **********
292 2012-08-04 18:00 30 ***********
... ..( 3 skipped). .. ***********
296 2012-08-04 18:04 30 ***********
297 2012-08-04 18:05 31 ************
298 2012-08-04 18:06 31 ************
299 2012-08-04 18:07 31 ************
300 2012-08-04 18:08 32 *************
301 2012-08-04 18:09 33 **************
... ..( 2 skipped). .. **************
304 2012-08-04 18:12 33 **************
305 2012-08-04 18:13 34 ***************
... ..( 3 skipped). .. ***************
309 2012-08-04 18:17 34 ***************
310 2012-08-04 18:18 35 ****************
311 2012-08-04 18:19 35 ****************
312 2012-08-04 18:20 36 *****************
... ..( 2 skipped). .. *****************
315 2012-08-04 18:23 36 *****************
316 2012-08-04 18:24 35 ****************
317 2012-08-04 18:25 36 *****************
... ..( 2 skipped). .. *****************
320 2012-08-04 18:28 36 *****************
321 2012-08-04 18:29 35 ****************
322 2012-08-04 18:30 36 *****************
... ..( 8 skipped). .. *****************
331 2012-08-04 18:39 36 *****************
332 2012-08-04 18:40 37 ******************
333 2012-08-04 18:41 38 *******************
... ..( 39 skipped). .. *******************
373 2012-08-04 19:21 38 *******************
374 2012-08-04 19:22 39 ********************
... ..( 25 skipped). .. ********************
400 2012-08-04 19:48 39 ********************
SCT Error Recovery Control:
Read: Disabled
Write: Disabled
SATA Phy Event Counters (GP Log 0x11)
ID Size Value Description
0x0001 2 0 Command failed due to ICRC error
0x0002 2 0 R_ERR response for data FIS
0x0003 2 0 R_ERR response for device-to-host data FIS
0x0004 2 0 R_ERR response for host-to-device data FIS
0x0005 2 0 R_ERR response for non-data FIS
0x0006 2 0 R_ERR response for device-to-host non-data FIS
0x0007 2 0 R_ERR response for host-to-device non-data FIS
0x000a 2 1 Device-to-host register FISes sent due to a COMRESET
0x8000 4 1463 Vendor specific